Lonsdor K518 Program Mazda3 Alexa 2017 Smart Key

Guide to add smart key and program all keys lost on a Mazda3 Alexa 2017 by Lonsdor K518 key programmer via OBD.

Key information:

Chip type: special smart card

Frequency: 433MHz

Pin code: No

Remote generation: smart key programming completed will generate remote automatically

Device to program: Lonsdor K518ISE (English version of K518)

OBD location: Under the steering wheel

19-1
19-2 19-3

1: Add smart key

Connect K518 from Obd2tool.com host with vehicle via diagnostic socket

Select Immobilizer->Mazda->Alexa

Communicating…

K518 read part number

19-4

Turn ignition switch to ON position

19-5

K518 identified key programmed: 2
19-6

Communicating…

Stick the non-registered smart key on the Start button

19-7

Programming…

Automatic model please step on the pedal brake

Manual model please step on the clutch

19-8

Programming…

Identify key programmed: 3

19-9

Turn ignition OFF

All programmed key must perform following operations:

Step on pedal brake, press on Start button with remote key with car logo mark and start turn IGN ON

Turn IGN OFF after 3s

19-10

Program success

19-11

1: All keys lost

Connect K518ISE host with vehicle via diagnostic socket

Select Immobilizer->Mazda->Alexa

Communicating…

K518 read part number

Require at least 2 keys
19-12

Turn ignition ON. If cannot switch ignition on, please press on Cancel button

19-13

Communicating…

Key programmed:3

19-14

Communicating…

19-15

Lonsdor K518ISE identified key programmed: 0

19-16

Turn ignition OFF

19-17

Hold non-registered smart key in hand

19-18

Turn ignition ON

Stick 1st smart key with logo on the Start button

19-19

Programming…

Key programmed:1

19-20

Turn ignition off

Hold non-registered smart key in hand

Turn ignition ON

Stick 2nd smart key with logo on the Start button

19-21

Programming…

Key programmed: 2

19-22

Turn ignition OFF

All programmed key must perform following operations:

Step on pedal brake, press on Start button with remote key with car logo mark and start turn IGN ON

Turn IGN OFF after 3s

19-23
Program success.

19-24

Lonsdor K518ISE reads Renault Citroen Peugeot PIN code

Lonsdor K518ISE pin code reading coverage on Renault, Citroen & Peugeot:

for Renault pin code coverage, the Renal system has fixed pin code to choose, Renault Immobilizer System 2  only for Renault Koleos after 2011 year which needs to remove the immo;

for Citroen and Peugeot pin code coverage, the old type is not supported, for example, 206 and 207.

Lonsdor K518ISE Renault coverage:

9-1

Lonsdor K518ISE Citroen coverage:

9-29-2

Lonsdor K518ISE Peugeot coverage:

9-3

The above coverage is for reference, any questions click on www.obd2tool.com and click Live Support to get instant reply, or contact email at Sales@obd2tool.com for best price.

Good luck with you.

Lonsdor K518 Program VW Polo 2009 4th IMMO NEC+24C32 Remote Key

Here’s the demo guide on programming VW Polo year 2009 4th IMMO NEC+24C32 smart remote key with Lonsdor K518 key programmer by OBD.

Key information:

Original key: 3-button folding remote key

Frequency: 433MHz

Chip type: Special ID48 chip (TP23)

Device to program: Lonsdor K518ISE key programmer

4-1
Procedure:

Connect K518 host with vehicle via OBD diagnostic socket

Select Immobilizer->VAG->4th Immobilizer->Identify Immo type

4-2 4-3 4-4

Lonsdor K518 identified immo type: 4th IMMO

4-5
K518 from www.obd2tool.com detect vehicle part number and immo type

4-6
Select NEC 24C32

4-7

Then Backup EEPROM and save data

4-8 4-9

Select Read Immobilizer data

4-10

Lonsdor K518ISE at OBD2 key programmer read vehicle information: VIN, CS, PIN, key number and key ID

4-11

Select Make Dealer Key

4-12

Push card slot on K518 main unit from right direction

Insert new key to be programmed into card slot

4-13 4-14

Select Key Learn

4-15

Enter key number to be programmed (keys that will start vehicle )

4-16

Insert key and turn ignition on one by one

I.E, Dashboard shows 1-2 means 1 key has been learnt, 2-2 means 2 keys have done

4-17

Program success.

4-18

Test remote and star car.

How to Program BMW F30 FEM Key with CGDI Prog Key Programmer

Here’s the little guide on programming key on a BMW F30 FEM system with CGDI Prog BMW MSV80 Car Key Programmer.

Device required:

CGDI Prog BMW key programmer

BMW FEM/BDC Test Platform for BMW  F20 F30 F35 X5 X6 I3

Preparation:

Disassemble the FEM/BDC module from vehicle

Procedure:

Connect BMW FEM/BDC test platform with CGDI Prog and FEM/BDC module from Obd2tool.com

cgdi-prog-1

cgdi-prog-2
cgdi-prog-3

Open CGDI Prog BMW software

cgdi-prog-4
Select FEM/BDC Key Match

cgdi-prog-5

The current FEM BDC needs to update the ECU program before performing key matching. Please ensure that the car battery has enough power supply. Please do not disconnect cable connection during programming procedure.

cgdi-prog-6

Please remove the FEM BDC and then use the programmer to read and save the data from the
95xxx EEPROM chip on the FEM/BDC computer board, then click “Next”
cgdi-prog-7
Please read the original car EEPROM data

cgdi-prog-8

cgdi-prog-9
cgdi-prog-10

cgdi-prog-11

Read eeprom data with Key Programm Tool, i.e Orange 5 eeprom programmer

and save data

cgdi-prog-12

cgdi-prog-13

User the programmer to write the calculated new data to the 95xxx eeprom chip, then put the FEM BDC back to the car
click Next

cgdi-prog-14
Click OK to write M95128

User the programmer to write the calcutaed new data to the 95xxx eeprom chip, then put the FEM BDC back to the car
click Next

Power on BMW FEM BDC test platform

The yellow indicator will flash

cgdi-prog-15
cgdi-prog-16

Coding is being backed up

The ECU is being programmed

and verify flashing

cgdi-prog-17

cgdi-prog-18

Program BMW F30 FEM key success

cgdi-prog-19

How to use SKP1000 to add Honda Accord 2012 key

Guide to add a smart key on Honda Accord 2012 by using SKP1000 tablet key programmer.

Key information:

Original key: 3-button Smart key
Frequency: 433MHz
Chip: 47
Slot: Without slot
Device: SKP1000 tablet car key programmer

Procedure:

(Note: The guide was provided by a Chinese locksmith A Jie using SKP 1000 Chinese version CI600 Plus)

Connect Automotive Key Programmer SKP1000 key programmer with vehicle, Turn igniwion to ON position
Select Honda

19-1
Select By System

19-2

Select Smart Key System 1-> Smart key system

19-3 19-4

Select Add a smart key

19-5

Take away all smart keys out of car

Press YES to continue

19-6

Put a registered smart key inside the car

Press YES

19-7

Take away the smart key out of car

19-8

Insert a new smart key inside the car

Press YES

19-9

Turn ignition switch OFF within 15s

19-10

Turn ignition ON

Turn ignition OFF

Turn ignition ON again
19-11

19-12

19-13
Dashboard immo indicator go off

Press YES if indicator turn off

19-14

19-15

Turn ignition OFF

Turn ignition ON

19-16

19-17

SKP-1000 register Honda Accord 2012 smart key success

19-18

Press NO to go back.

Test the new smart key.

How to use SKP1000 to Program Koleos 2015 Smart Card

Guide to program Renault Koleos 2015 year smart card to enable one-button Start Stop feature by using SKP1000 Key Programmer via OBD.

14-00

(Note: The tutorial was provide by a Chinese engineer on a locksmith forum using OBD2 key programmer SKP1000 Chinese version Lonsdor CI600 Plus key programmer)
There is no single device that will read Renault pin code by OBD, can only read data by removing the BCM and then to calculate the security pin code.
Step 1: Remove BCM

14-01 14-02 14-03
Remove BCM under the dash
Step 2: Disamble BCM
, find out and locate CPU 0M23S

14-04 14-05
Step 3: Read CPU data
In Xhorse VVDI Prog programmer, select Immobilizer->Renault BCM-XDT384- 1L15Y is the same as 0M23S

14-1

Follow VVDI prog wiring diagram to connect

14-2 14-3 14-4 14-5
Save data

14-6 14-7

Step 5:  Calculate pin code
Send the BCM data to our engineer or Lonsdor factory engineer to calculate pin code within several minutes.
Here is the pin code for this car: 33EB 2FE6 78CD
Step 6: Smart Card Learning
Do smart card as well original smart card learning by SKP-1000 key programmer

14-8 14-9 14-10 14-11

Select Renault->By Vehicle->Koleos->Immobilizer system

14-12 14-13
Choose OBDII connector
Press on the Start button
Press YES to continue

14-14
Select Program Smart card
Open the door on the driver side

14-15
Manually enter security code calculated by engineer, and confirm

14-16 14-17

Insert the smart card to be programmed
Press YES to continue
14-18 14-19
Configuring…
Program success
Continue to program next key?
Press YES to continue

14-20

Insert the next smart key to be programmed
Follow procedure above
Until Program success.

14-21

Done!

Difference between skp900 and skp1000 key programmer

skp1000 key programmer is work better than old skp900 key programmer.  their pictures as following:

skp1000skp900

 

what is the mainly difference between them ?

1.  their outside appearance is not same.

2.  Skp900 key programmer supports auto key programming ONLY!  but Skp1000 obd2 key programmer supports auto key programming + special functions!

3.  skp900 auto key programmer not support special functions, but skp1000 auto key programmer can support special functions. such as OBD mileage adjustment, remote controller, oil/service reset, throttle body adjustment, EPB, pin code calculation,EEPROM chip read, immobilizer initialization,EEPROM/PIC adapter,personalized settings etc.

4. SKP1000 will be compatibility for future cars,  SKP900 stopped production and never works for new models

skp1000 key programmer is easy to use, This is how to use SKP1000 key programmer:

connect the main cable to the SKP 1000 machine

plug the OBDII adapter to the car

power on the SKP1000 machine, until you see the LOGO

press [YES] to the main menu

choose “Immobilizer”

1

go to the SKP 1000 car list

choose a model: Hyundai, press “Confirm”

2

choose “Smart card”, press “Yes”

3

choose ” by car model”, press “Yes”

4

choose “SONATA 8 (with card slot), press “Yes”

5

choose “Smart card (with card slot), press “Yes”

6

follow the prompt on the screen to turn off ignition, press “Yes

7

open the door and close for one time, press “Yes”

choose smart card to match, press “Yes”

8

insert the smart card into the slot, and you can hear alarm sound, turn off the ignition, press “Yes”

9

input the password

10

check if the password is correct, press “Yes” to confirm

11

program the first smart card successfully

press “Yes” to program the next one

press “No” to complete key programming

12

13

14

SKP1000 tablet key programmer User manual

10-1

1. Product description

10-2

1.1 Supported protocol:
SAE-J1850 PWM, SAE-J1850 VPW, KWP2000, ISO-9141, CANBUS, SINGLE CAN

1.2 Package Includes:
1* Main unit
1* touch pen
1* main cable
1* Honda 3pin adapter
1* Kia 20pin adapter
1* Hyundai / Kia 10pin adapter
1* Haima 7pin adapter
1* power adapter
1* TF card
1* TF card reader
1* USB cable
1* CD with user manual

2. Menu Instruction

10-3

2.10 Main menu basic functions
Car functions
Choose ” Car functions” to perform immobilizer, mileage adjustment, remote controller,
Oil/service Reset, throttle body adjustment,?EPB, pin code calculation, personalized settings and special function

10-4

2.11 immobilizer function:
Clear key memory;
Program keys, proximity keys, smart key, flip keys;
Program after-market and OEM keys;
Read keys from immobilizer memory
New mechanical key number programming;
Vehicle identification key programming;
Reset ECU& Reset immobilizer;

10-5
2.12 Mileage adjustment via OBD

10-6
10-7
2.13 New remote controller programming
10-8
2.14  Oil/Service reset

10-9
2.15 throttle body adjustment
10-10

2.16 EPB(Electric park brake)
10-11

2.17 Immo PINCODE reading
.Immo PINCODE reader?for many vehicles?and no need pincode when programming keys for many vehicles.

10-12

2.18 Personalized settings

10-13
2.19 Special functions
Plug into the adapter that paid extra money to perform special functions.

2.20 System settings
Choose ” System settings” to read the machine basic info.

2.21 Firmware upgrade
Choose ” Firmware upgrade” to update the machine firmware.

10-14

10-15

10-16

10-17

2.22 User program test
Choose “User program test” to reset the SKP1000 machine at www.obd2tool.com to collect corresponding data.

3. How to use SKP1000 to program key on specific car model?
Step-by-step procedure:
For example, to operate Hyundai SONATA 8 smart remote controller, firstly connect the main cable to the machine, then plug the OBDII adapter to the car.
Power on the SKP1000 tablet key programmer machine, until you see the LOGO, press [YES] to main menu, Choose “Immobilizer”, press “Confirm” to vehicle list.

10-18

10-19

10-20

Choose model: Hyundai, press “Confirm” to enter.
Choose “Smart card”, press “Yes” to enter.
Choose ” by car model”, press “Yes” to enter.
Choose “SONATA 8 (with card slot), press “Yes” to enter.
Choose “Smart card (with card slot), press “Yes” to enter.
Follow the tip to turn off ignition, press “Yes”
Follow the tip to open the door and close for one time, press “Yes”.
Choose smart card to match, press “Yes”
Follow the tip, insert the smart card into the slot, and you can hear alarm sound, turn off the ignition, press “Yes”.
Input the password
Check if the password is correct, press “Yes” to confirm.
The first smart card program successfully, and it will ask you if you program the next one, press “Yes” to confirm.
Insert the second smart card into the slot, you can hear the alarm sound, press “Yes”.
Program successfully, press “No” to back.
With two new smart card keys, you could start the car, if you need to add more keys, just repeat the above steps.

4. Firmware update
Before update firmware, please take out the TF card and insert it into the card reader, then plug into the computer USB port. Double click “My Computer”, find out ” local Disk (H:), right click to choose “Format”.

10-21

Tip: Tick on the “Quick format” and click “Start.
After complete format, go to the official site to download the update file, then copy and paste the file into the TF card, after finish, plug the TF card into the machine, power on the machine to the main interface.
10-22

Click on “Firmware update”.

10-23

Firstly choose “System firmware update”, press “Yes”, the procedure shown as below:

10-24
Update successfully shown as below.

10-25

Press “No” to back.
10-26

Choose ” Adapter firmware update”, after finish, reboot the machine to go on use Auto Key Programmer SKP1000.

Done.

Any question, please contact your supplier.

5-01

SKP1000 key pro OK to program 2014 Maserati Ghibli smart key

This post is on how to use SKP1000 programmer to program smart key on 2014 Maserati Ghibli.

Let’s go.

1. Choose the last option “Smart key (New)”
5-01

Immo system
5-02

It displays instruction “Please choose: OBDII Port and turn on ignition, press “Yes” to continue and “No” to back.
5-03
Note: SKP1000 can program key when all key lost and add new key, if all key lost you do not need to turn on ignition.

Choose “Pincode read”
5-04

Read out Pin code, click “No” to back to choose “Add smart key”
5-05

Please turn on “Emergency light” and turn off ignition, click “Yes” to continue.
5-06

Leave the smart keys you want to program in the car and take the other keys out of car.
Choose “Yes” to continue, and “No” to back.
5-07
Input the pin code.
5-08
Configuring the system, please wait
5-09

In 30 seconds, close the Obd2tool.com SKP1000 to the start button on the car and press the “Unlock” button on the machine, press “Yes” to continue.
5-10

Complete program smart key with Automotive Key Programmer SKP1000 tablet key pro.

5-11

5-12