How do I download the latest firmware to my INLINE 6 or INLINE 5 adapter?

This indicates that the adapter has experienced a failure or the memory was corrupted while trying to download new firmware to the adapter. Try removing power and reapplying it, waiting for several seconds to see if the adapter resumes normal operation. If it doesn’t, try downloading the latest software, carefully following instructions on the INLINE 6 software download web page or the INLINE 5 software download web page. If this also fails to work and the adapter is still under warranty, contact your authorized Cummins distributor.

3.Why doesn’t my INLINE 6 or INLINE 5 adapter work with INSITE version 5.4 or other older Cummins software applications?

Versions of INSITE earlier than 6.3 may not be RP1210 compatible. Since the INLINE 6 and INLINE 5 adapters use the RP1210 protocol, they will only work with software that supports the RP1210 protocol. Visit the Compatibility pages on this site to determine what versions of Cummins software applications are compatible with RP1210 and the INLINE 6 and INLINE 5 adapters.

4.Will the INLINE 6 and INLINE 5 adapters work with my QuickCheck III software?

The INLINE 6 and INLINE 5 adapters will not work with the QuickCheck III software.

5.Will the INLINE 6 and INLINE 5 adapters work with non-Cummins RP1210-compatible software applications?

As long as these non-Cummins software applications are truly RP1210-compliant, the Cummins INLINE 6 and INLINE 5 adapters will work with them. However, some non-Cummins applications have proprietary features that make them not fully compliant with the RP1210 standard and they will not work properly with the INLINE 6 and INLINE 5 adapters. Test the application with an INLINE 6 or INLINE 5 adapter to verify compatibility.

6.How do I download the latest PC driver for my INLINE 6 or INLINE 5 adapter?

Download the latest PC driver for your adapter. Note that the INLINE 6 driver and INLINE 5 driver are different and you must use the correct driver for your adapter.

7.How do I download the latest firmware to my INLINE 6 or INLINE 5 adapter?

Download new firmware from the Software Downloads section of this page. Before you download the firmware, verify that the version is newer than what is already in your adapter, which you can find by double-clicking on the INLINE 6/5 tray icon on your computer. Note that you will need the Flash reprogramming utility described below to reprogram firmware in the INLINE 4 and INLINE 5 adapters. Note that the INLINE 6 firmware and INLINE 5 firmware are different and you must use the correct firmware for your adapter.

8.Why am I having issues with the DEF gauge?

INLINE 4: Use Driver Version 5.7.0.1, which has version 4.47 of the firmware.
INLINE 5: Use Driver Version 5.7.0.1, which has version 5.47 of the firmware.

9.How do I know my Inline adapters compatibility?

INLINE 5 and 6 are compatible with both PowerSpec and Insite.
PowerSpec versions of 4.2 and later support the RP1210 protocol and are thus compatible with the INLINE 6 and INLINE 5 adapters. See the chart below for an example of the basic connections needed to hook-up to the vehicle data link.
INSITE versions of 7.5 and later are compatible with the INLINE 6 and INLINE 5. Note that INSITE versions earlier than this are not fully RP1210B compliant and may not work with these adapters. See the chart below for an example of the basic connections needed to hook-up to the vehicle data link.

10.Does Cummins Support other RP1210 Devices with their Electronic Service Tools?

Heavy Duty Truck Scanner Tool like INSITE and Fault Viewer are RP1210 compatible but adapters other than those Cummins adapters are supported by the companies that produce them. The Electronic Service Tools help desk will help diagnose tool issues, however, it is highly recommended any communication issues with non-Cummins adapters should be brought to the adapters support group first before calling Cummins. In most causes, the issue is known or they have a fix they can give you to work around a problem until a driver update is available.

(Solved) Cummins Insite ECM Connection Error 5204

Here you go… How to solve Cummins Insite 8.1 Connection Error 5204 5202 5201 5200

with DPA5 Adapter, i try to connect with Cummins insite and i have error code 5204 or only no connection and not blinking the leds

This is the error 5204 popped up when connect Prostar 2005 with cummins engine:
ECM connection
Error number: 5204

Communication between the datalink adapter and the ECM could not be established BY Heavy Duty Scanner.

Please check the following conditions:
The key switch is on
The cables are between the datalink and the ECM are properly connected
The cables are in good condition
The correct adapter type is selected
The correct communication protocol is selected

Select retry, cancel or help for additional troubleshooting steps

http://forobd2tool.com/wp-content/uploads/2017/06/15-1.jpg

Here is what have been tried but failed!

Try to connect whit J1939…..same issue

On truck does not even get the engine and the others only couple line and very slow, might be some thing with them trucks

some things odd2006 models connect through J1939 and works.
Tryed on 3 trucks already that are 2005 and older the connect thought J1708 it says engine 128
And when doing the J 1939 test on them it says something like data error

Check the driver is installed well

J1939 & J1708 are added to the software

Finally, SOLVED!

The solution is this, connect, then scan to diagnostic connector but not to USB, open the Cummins insite and push connect, when the Insite begin to connect, immediately connect the USB and ready….

The final tip- Error Messages for communication failures:

Error 5200: Indicates communication loss between computer and the datalink adapter.

Error 5201: Indicates communication loss between the datalink adapter and the ECM.

Error 5202: Indicates no communication could be established between the datalink adapter and the computer.

Error 5204: Indicates no communication could be established between the datalink adapter and the ECM.

If the “Auto Configure” and/or “Datalink Adapter Connection Test” do not find the adapter when connected, manually configure the Cummins INLINE 6 Data link adapter connection.

Top 5 Reasons to Get INLINE 6

Cummins INLINE 6 data link adapter is an cummins engine diagnostic tool that’s designed to connect an external computer to a vehicle’s onboard computer for Cummins engine diagnosis purposes. Cummins inline 6 diesel engine usb kit is cummins inline 5 update version.

Top 5 Reasons to Get INLINE 6
1. The INLINE 6 can communicate with your PC through a 9-pin serial connector. The INLINE 6 also can communicate with your PC over a Universal Serial Bus (USB) through a 4-pin standard connector. The INLINE 6 adapter connects to vehicle power, the SAE J1708/J1587 data link, and two CAN/J1939 data links via a 25-pin serial connector.
2. With full compliance to the Technology and Maintenance Council’s RP1210 standard, the INLINE 6 will work with the latest Cummins INSITE, PowerSpec and Calterm III software applications.
3. It will also work with any other software applications that are fully compliant with the RP1210 standard (note that while some non-Cummins applications fully support RP1210, others do not, so you should test each application in question with the INLINE 6 adapter to make that determination).
4. The eye-catching INLINE 6 breaks new ground by utilizing the latest electronic technology to deliver high performance and high quality at an attractive price.
5. Each Cummins INLINE kit contains a data link adapter, basic cables, and the INLINE PC software driver. Load the software driver, connect all the hardware, and you are ready to start a new era in data link adapters.

Autel ms906 from obd2tool.com work function better than ds708 with fast run speed. Runner Faster Than DS708 and highly recommend. The Autel Ms906 MaxiSYS is a revolutionary, ultra-mobile solution for automotive diagnostics. The MaxiSYS Mini comes with a powerful A9 quad-core processor and comprehensive OE-level vehicle coverage. The multitasking Android Operating system is capable of coding, adaptations, actuations and much more.

Weighing in at only 1.5 lbs. with a crystal clear 7.9 screen, the MaxiSYS MS906 helps you organize information, diagnose complex vehicle symptoms and analyze fault codes quickly, easily and efficiently. The optional connector kit (P/N: MS905-CONKIT) allows MaxiSYS Mini users to access older vehicles ABS/SRS systems that cannot be accessed through the 16-pin OBD-II DLC connector. The MaxiSYS Mini comes with the standard 16-pin OBD-II DLC connector, wireless Vehicle Communication Interface (VCI), software for Domestic, Asian, & European vehicles, and one year of FREE updates.

Difference Between Cummins INLINE 5 and Cummins INLINE 6

Cummins-INLINE-5-and-Cummins-INLINE-6-

Difference Between Cummins INLINE 5 and Cummins INLINE 6
1. Cummins INLINE 5 usb cable is 2 meter, Cummins INLINE 6 is 3 meter
2.Cummins INLINE 5 DB25F/6-pin data link cable and OBDII 16pin cable
Cummins INLINE 6 DB25F/3-pin/2-pin/2-pin cable
3.With Different Version Software

For very heavy duty vehicles, the Cummins M series engines, which are 10.8 litre straight sixes, are often used. Used truck engines can be picked up from a variety of places, though knowing which type of engine you require and how much the going price is, can help to ensure that you receive a great engine at a suitable price. Hopefully this article has helped you, or at least shown you some of the options available.

How To register the Autel MS906 diagnostic scanner:
1. Visit the website: http://pro.autel.com.
2. On the Sign In page, input your account ID and other information to log in, if you already have an account.
3. If you are a new member to Autel and do not have an account yet, click the Create Autel ID button on the left side.
4. Enter the required information in the input fields, read through Autel’s Terms and Conditions and tick on Agree, and then click Create MaxiSYS MS906 ID at the bottom to continue.
5. The online system will automatically send a confirmation email to the registered email address. Validate your account by clicking the link provided through the mail. A product registration screen opens.
6. Find out the device’s serial number and password from the About section of the Settings application on the display tablet.
7. Select the product model of your device, enter the product serial number and password on the Product Registration screen, and click Submit to complete the registration procedure