Porshe PIWIS 2 – дилерский сканер Porsche

26-1

Данный сканер Porsche Piwis 2 является новейшим оборудованием для диагностики автомобилей Porshe. Прибор заменил предыдущую версию автосканера Porshe PIWIS ( поддерживал модели до 2010 года) и применим ко всем моделям до 2012 года включительно, в том числе с новым Porsche Cayenne и Porsche Panamera. Предназначен как для диагностики , так и для программирования ЭБУ.

Дилерский автосканер Porsche Piwis Tester 2 состоит из ноутбука, на котором находится программный модуль сканера, и блока для подключения к автомобилю. PIWIS2 совместим со всем модельным рядом Porsche.

Функциональность диагностического сканера Porsche PIWIS 2

* диагностика ЭБУ
* адаптация
* программирование блоков управления
* управления исполнительными механизмами
* поиск неисправностей
* замер и анализ рабочих параметров системы.
* выполнение сервисных функции.

В комплект поставки диагностического комплекса Porsche PIWIS II входит:

* Оригинальный интерфейс Porsche Piwis2
* Ноутбук с установленным программным обеспечением
* Диагностический кабель OBDII
* Кабель для соединения ноутбука и интерфейса
* Panasonic CF29 ( б.у.) с установленным программным обеспечением.
* DVD для восстановления системы

How to do BMW G Series Coding with BMW ICOM cable

Topic: How to do BMW G Series Coding with BMW ICOM cable

I’ve collect all useful tips of BMW G series coding on the web and make a write-up here. Hope it helps.

Q: Is it possible to code BMW G-series and wich software? E-sys is not possible?

A: Coding G series is with ESYS. I think you need pro launcher from Tokenmaster. It was written somewhere on the forum but maybee you can ask Tokenmaster.

Q: Have any good success if G series coding?

A: I have successfully coded G-series. You need Pro Launcher.

Q: Do we know if it’s possible at all to code the G-series?

A: Coding is possible with E-SYS, but problem is the mapping/trimmed CAFD’s on new ECU’s. But for excisting ECU’s not a problem (BDC_BODY, NBT2, ACSM etc.)

Q: Can I code G11 with Esys?

A: Tried to code G11 today.

My I-level is S15A-16-07-506, used data 5.94.

I found S15A target in Esys.

S15A psdzdata covers F090/G001/G002/G011/G012/G030/G031/G032/RR11/RR12/RR31

Q: Could you share with me your launcher pro’s token and activation code ?

A: This is not possible. Token and activation code are valid for 1 PC only. This is how it works: you ask Token Master, he sends token, you install Launcher Pro with the token, Launcher generates request code, you send it to Token Master, he sends you activation code in response.

Q: Which E-sys can be used for G series coding?

A: E-Sys:
S15A psdzdata covers G001/G002/G011/G012/G013/G030/G031/G032
S15C psdzdata covers G008/G038

Q: Which tool for G series?

A: I’m perfectly aware what ICOM Next from OBD2TOOL is and I have it.

Icom next runs a gigabyte lan port. So if router and laptop also running gigabyte ports you increase speed, that’s only if the car and software allow it.

Also the Icom next is faster for G series cars which I suspect also have gigabyte Ethernet bus.

Also it has USB3.0 instead of USB2.0 and a better wifi card.

Ps. It’s a copy, from http://www.obd2tool.com/search-BMW+ICOM.html

Q: Which BMW ICOM can i use for G30?

A: Any icom will work , but to be safe with f,g,i series vehicles , use a dedicated router as kafas huh and a few other modules will crash if you do not use a router it handles the switches for Ethernet as those modules use more than 1 path way , in short it uses all 4 two pair wires and without router not good , this has worked for me for some time now good luck. note my router does not connect to wan

Q: What tool is used for G30 flash or coding?

A: Flashed all Cars with BMW ICOM Next and Online Aos with DHCP over Router. Since that i have Never any Problems with NBT or other. Flash E/F/G with this Setup.

Note that Online Aos is the online version of the BMW software for Diagnostic, Programming any many other things.

Q: How to do G30 coding?

A: BMW G30 has a quite a lot of differences in ECU, so wanted to share my findings here.

Note:

– This is Not a comprehensive list of options But options that are unique from options standard across the recent models.

– Read SVT does Not work, use Read ECU instead.

– Ensure vehicle engine is running before you press Read ECU button otherwise you won’t get the full list of ECUs.

ECU: SAS [Driver Assistance Systems]

ACC Default Distance: C_Abstandsstufe_init -> Set to 2

Blind Spot Detection: Note that G30 has a multiple Blind Spot Detection Modules, and you need to set Speed setting for each. For each radar module there is a separate KMH and MPH Setting so 6 in all.

E.g.

C_LCA_SWW_Vmin_KMH – set to 55km/h

C_LCA_SWW_Vmin_MPH – set to Option 0 (Werte 22)

ECU: HU_NBT [Head Unit]

G30 has a hardware limitation and max Video-In-Motion you can get via E-sys is 63 km/h (around 39 mph). After following standard VIM coding, Ensure that

SPEEDLOCK_SPEEDVALUE_MIN: Werte=1F

SPEEDLOCK_SPEEDVALUE_MAX: Werte=3F

ECU: DKOMBI [Instrument Cluster]

Remove Speed Limit Sign from HUD: HUD_SPEED_LIMIT_ENABLE DKOMBI

ECU: IHKA [Climate Control] – Not Tested

This encoding value determines whether the previous settings (Last Function) should be used when switching from the Auto mode to Manual mode, in manual mode, or whether the settings from “Auto” should be used when changing from the car to the manual mode.

LAST_FCT_AUTO_MAN

Default: AKTIV (Active) = 01

HO coding in order to be able to manipulate front-end adjustment of the ventilation (if necessary, in the case of special large-scale customer requests)

3003 -> VERTRIMMUNG_BEL_FRONT (Front Face)

keine = 00

3003 -> VERTRIMMUNG_FUSS_FRONT (Front Feet)

keine = 00

OPTIONS

keine = 00 (No)

kaelter = 01 (Colder)

waermer = 02 (Warmer)

ECU: BDC_Body -> 1DF7 – Comfort Access Settings

3514 PMaster Has Comfort Access Related Settings

ECU: ACSM – Safety Related Settings

Settings for SeatBelt Reminders and such

Clone Xentry Connect C5- Good & Bad Things

I bought “Original Clone Xentry Connect C5” from China’s retail store Obd2tool.com in 2017/12.

Good thing:

1. Unlike bad products of C5 type C4 motherboard, texture is good
2. DoIP specification

Bad thing:

1. Because it is VM system + 32bit, the reaction is slow (SSD though …)
2. Vediamo can be used, but feeling like driving with DELL D 630 (unsuitable)
3. The DTS Monaco software is installed but the connection with the vehicle is NG (currently retail stores and manufacturer engineers are thinking about how to fix it)
4. Passwords are applied to each drive, making it hard to customize
5. Retail shops and manufacturer engineers lack knowledge (take time to support)

My thoughts

I think purchasing this product is still early.

There are too many trouble elements.

I’ll report it when the situation changes.

What I currently use (stable and comfortable)

New car: eCom (64 bit)
Normal: Clone SDConnect C4 (64 bit)
Old car: Clone C3

Best regards

BMW FEMBDC New Key Programming by YH BMW FEM Programmer

Here comes the easy step by step guide on how to use YH BMW FEM Programmer to add key for BMW FEM/BDC vehicle models.

Summary:

Preparation
Step 1:Backup(read) coding data

Step 2:Update ECU

Step 3:Add key

Step 4:Recover(write) coding data

Preparation:

Connect the OBD2 socket of BMW FEM BDC to vehicle.

11-1

Here comes the easy step by step guide on how to use YH BMW FEM programmer to add key for BMW FEM/BDC vehicle models. Summary: Preparation

Step 1:Backup(read) coding data

Step 2:Update ECU

Step 3:Add key
Step 4:Recover(write) coding data Preparation:

Connect the OBD2 socket of BMW FEM BDC to vehicle.

1 Connect the USB cable of Yanhua BMW FEM Key Programmer with laptop
2 Turn on the ignition,keep the vehicle battery voltage on less than 13.0 V. Step 1:Backup(read) coding data Perform “Backup(read) coding data”,and save the data.
3 Wait for system “Executing read coding data cache…”
4 After data reading complete,save the data file on your laptop.The data file you saved is use for Step 4.Check the file data format,it is BIN.
5 Step 2:Update ECU. Open the vehicle switch,click the Step 2 button to update ECU
6 Software pop-up the follow tips,please follow instructions to disconnect battery and other charging device,remove the FEM/BDC,use car universal programmer(for example:YH CKM100) to read EEPROM data,save in BIN format in PC.
7 Remove the FEM/BDC. The FEM/BDC is located at the lower part of the A column at the front passenger side. Note:Disconnect the car battery and other charging equipment when removing and installing the FEM/BDC.
8 EEPROM position and pin direction 9 Please use car universal programmer,such as YH CKM100 to read out EEPROM data,and save the data file on your laptop. 10 After finishing above operations,please go back to the YH BMW FEM/BDC software interface and click “Ok”.
11 The software will prompt to load the original EEPROM data which was read from the vehicle by programmer.
12 Then system will calculate the corresponding new EEPROM data and prompts the user to save ti.(Save in BIN format as well)
13 The software prompts to write the newly generated EEPROM data back to EEPROM chip.Solder the EEPROM back to FEM/BDC.Install the FEM/BDC back to vehicle.Recover normal power supply for vehicle and turn on the ignition. Step 3:Add Key Turn on the ignition,click “Step 3: Add key”
14 According to the software prompt,put the working key close to the coil(located on the lower right of the steering wheel).
15 The software reads and displays the relevant information about the working key. Note:Keep the key close to the emergency starting antenna until the key information is reached.
16 Then software will pop-up key list,the user can choose key which need to be added.Learn the key number and click “Learn new key”(Recommend to use the key number sequentially and in turn)
17 According to the software prompt,the new key is close to the emergency starting induction antenna(located on the lower right of the steering wheel)
18 Key information will be showed after the new key is close to emergency start antenna.
19 After adding the key and learning,the software returns and refreshes the key list.Users can continue to add and learn more keys at this interface.If completed,click “Quit” Note:Please keep the key close to the emergency start induction antenna until the software pops up and refreshes the key list.
20 Step 4:Recover(Write) coding data Open the vehicle switch,click “Step 4:Recover(Write) coding data” button
21 Select the first backup coding data of the vehicle,recover it.
22 Successful recover coding data.Make full testing of vehicles and keys.
23 Test the remote control function of the key. Test the switch,engine start function of the key.

Connect the USB cable of YH BMW FEM BDC with laptop

11-2

Turn on the ignition,keep the vehicle battery voltage on less than 13.0 V.

Step 1:Backup(read) coding data

Perform “Backup(read) coding data”,and save the data.

11-3

Wait for system “Executing read coding data cache…”

11-4
After data reading complete,save the data file on your laptop.The data file you saved is use for Step 4.Check the file data format,it is BIN.

11-5

Step 2:Update ECU.

Open the vehicle switch,click the Step 2 button to update ECU

11-6

Software pop-up the follow tips,please follow instructions to disconnect battery and other charging device,remove the FEM/BDC,use car universal programmer(for example:YH CKM100) to read EEPROM data,save in BIN format in PC.

11-7

Remove the FEM/BDC.

The FEM/BDC is located at the lower part of the A column at the front passenger side.

Note:Disconnect the car battery and other charging equipment when removing and installing the FEM/BDC.

11-8

EEPROM position and pin direction

11-9

Please use car universal programmer,such as YH CKM100 to read out EEPROM data,and save the data file on your laptop.

11-10

After finishing above operations,please go back to the YH BMW FEM/BDC software interface and click “Ok”.
11-11

The software will prompt to load the original EEPROM data which was read from the vehicle by programmer.

11-12
Then system will calculate the corresponding new EEPROM data and prompts the user to save ti.(Save in BIN format as well)

11-13

The software prompts to write the newly generated EEPROM data back to EEPROM chip.Solder the EEPROM back to FEM/BDC.Install the FEM/BDC back to vehicle.Recover normal power supply for vehicle and turn on the ignition.

Step 3:Add Key

Turn on the ignition,click “Step 3: Add key”

11-14

According to the software prompt,put the working key close to the coil(located on the lower right of the steering wheel).

11-15

The software reads and displays the relevant information about the working key.

Note:Keep the key close to the emergency starting antenna until the key information is reached.

11-16

Then software will pop-up key list,the user can choose key which need to be added.Learn the key number and click “Learn new key”(Recommend to use the key number sequentially and in turn)

11-17

According to the software prompt,the new key is close to the emergency starting induction antenna(located on the lower right of the steering wheel)

11-18

Key information will be showed after the new key is close to emergency start antenna.

11-19

After adding the key and learning,the software returns and refreshes the key list.Users can continue to add and learn more keys at this interface.If completed,click “Quit”

Note:Please keep the key close to the emergency start induction antenna until the software pops up and refreshes the key list.

11-20

Step 4:Recover(Write) coding data

Open the vehicle switch,click “Step 4:Recover(Write) coding data” button

11-21

Select the first backup coding data of the vehicle,recover it.

11-22

Successful recover coding data.Make full testing of vehicles and keys.

11-23

Test the remote control function of the key.

Test the switch,engine start function of the key.

12.2017 XENTRYDAS Win 7 Win 10:Test OK

12.2017 XENTRY/DAS Windows 7 or Windows 10:

Both OK.12.2017 XENTRY OpenShell XDOS is updated and tested successfully for use. Download link:

http://www.obd2tool.com/goods-6841-MB+SD+Connect+C4C5+Star+Diagnosis+Plus+Panasonic+CF19+Laptop++With+Vediamo+and+DTS.html

But I don’t recommend windows 10 at all at least if you don’t know how to manage it
try windows 7 and I am asure you will be more comfortable]
final note, you need a good version which should not be manipulated or pre-activated

D-A-S / Xentry 2017.12….Confirmed!
Workshop Information System (WIS net) 2017.09….Confirmed!
Electronic Parts Catalog (EPC.net) 2017.09….Confirmed!
Part Location Finder (ST Finder) 2008/2016….Confirmed!
STARUTILITIES ….Confirmed!
SDMEDIA 2014….Confirmed!
Price List PL71 2016….Confirmed!

5-1 5-2

5-3

5-4 5-5 5-6 5-7 5-8 5-9 5-10

12.2017 XDOS Activation via Startkeycenter

This is the startkeycenter I used to activate 12.2017 Xdos with old keys. Move the folder to C:>PROGRAM FILES(x86)>MERCEDES BENZ. Launch startkeycenter from folder. Insert keys for xentry only. For DAS you should move the LIC.SLI file to C:PROGRAM FILES(x86)>MERCEDES BENZ>DAS>BIN which will activate it with no timeout. Blacklist is self explanatory which folders they should go in. I don’t claim any of this files…… I am just sharing which is what this Obd2tool.com is supposed to be about.

DSP3 Mileage Correction UPDATE

Condition of software update is connecting internet .Connect the OBD with host at first, then power on the system, software will be opened. Run ‘sm2007’, click Update — software update —Next, you can see Recognizing ID authorization , Download file, details see Figure. Video help file: CD:\DSP3\UPDATE.RMVB.

Before firmware update contact to smelecom.After authorized you can operate as softwre uptare.

29-1 29-2 29-3 29-4 29-5 29-6

DSP3 Mileage Correction Data Specialist Plus

1.PREFACE
The Data Specialist Plus is the most complete programming DSP 3 for digital odometers, airbag modules, car radios, car immobilizers. It is a high quality embedded system, which offers a maximum of flexibility and working comfort.

24-1
Outstanding characteristics of the system are:
-Based on ARM920 TDI, high frequency up to 400 MHz.
-800^480 TFT LCD and touch screen (7.0 inch.16:9).
-Convenient keyset.
-USB host and USB device.
-SD card interface.
-128MB NandFlash, 128MB SDRAM.
-Self-check function integrated in system.
-Automatic calculation of mileage or km for al cars.
-Automatic reset of airbag module.
-Automatic read code of IMMO or reset of IMMO ECU.
-Automatic read code or reset of car radio.
-Intuitive operability by full menu and picture guidance.
-Color connection picture is on the screen whenever you need.
-All data can be edited, stored and loaded.
-The stored data can be transferred to a PC by USB port or SD card, and also can be transfer to wherever you want directly by internet.
-EEPROM, EPROM and FLASH programming of MCU is supported.
-Strong ability for OBD functions, including CAN, J1850, ISO9141, and Keyword 2000 protocols.
-Upgrade directly from internet.

2.MAIN MACHINE
USB-host: for connection with PC.
USB-device: for connection of other USB device such as mouse, etc. SD card interface: for connection with SD card.
Adapter interface: for connection with adapters.
Power socket: for connection with 12V DC regulator.

24-2

3.ADAPTERS AND ACCESSORIES
Socket should plug into the adapter correctly, do not plug in the opposite side, otherwise will damage this machine or target board.
Eeprom Adapter is used to program eeprom memories, chips supported as follows:
SPI: X25043, X25045, 25C010, 25C020, 25C040, 25C080,25C160, 25C320, 25C640, 25C128, 25C256, 3132, 68343,ST14771, ST95010, ST95020, ST95040, ST95080, ST95160, ST95320,ST95640, X5043, X5045 and M35080(erase) included.

2C: 24C01, 24C01A, 24C02, 24C04, 24C0S, 24C16, 24C17, 24C32,24C64 24C12S, 24C256,005C72,005C002,005C92, BAW574252 etc.
MICROWIRE: 93C06, 93C14, 93C46, 93C56, 93C57, 93C66, 93C76,
93n006,93s46, 93S56, 93S57, 93S66, 93LC46, 93LC56, 93LC57,93Ln66, 93rn006, DY6N, LC46, L56R, SI 30, S220, etc.
OTHERS: such asPDHOOl, TC97101, TCOO9101, TCOO9102, TC009112, dd59, D6253, D6254, S-24H30, S-24H45, S-24S30,S-2445, 1691 IP 59cll,ac.

24-3

NDM457 Adapter supports the following chips: NDM457C, DELCO51006A etc

24-4

Motorola Adapter is used to program Motorola MCUs (without security),chips supported as follows:
6..HC05    series: MC6OOHC05B16, MC6OOHC05B32, MC6OOHC05B6, MCHC05BS, MC6OOHC05BE6, MC6OOHC05H12, MC6OOHC05L2S, MC6OOHC05P3, MC6OOHC05X16, MC6ooHC05x32,MC6ooHC705m6, MC6OOHC705B32, MC6OOHC705E6, etc.
7..HC0oogd3gnaNooHC0ooAZ32,MC6ooHC0ooAZ60,    MC6OOHC0OOAS32
M6OOHC0OOAS60, MC6OOHC0OOAB32, MC6OOHC0OOAS20, etc.
8..HC11    series: MC600HC1 IAS, MC600HC11E20, MC600HC11E9, MC600HC11EA9, MSooHnllFl, MC600HC11K1, MC600HC11K4, MC600HC11ICS2, MC600HC11ICS00, MC600HC11KA4, MC600HC11ICP MC600HC11IA MC600HC11P2, MC600HC11PA00,MC600HC11PHS, etc.

4).HC12 series: MC68HC912B32, MC68HC912BE32,MC68HC912BD32, MC68HC912D60,MC68HC912D60A,MC68HC912DG128, MC68HC912DG128A, MC68HC912DT128A, MC68HC912DT128A, MC9S12A64, MC9S12D64, MC9S12DG128, MC9S12DG256, MC9S12DP128, MC9S12DP256, MC9S12DT128, MC9S12H128,
MC9S12H256(including all flash) etc.

24-5

NEC Adapter is used to program upd7 8k0 series MCU’s, chips supported as follows:
uPD780973,uPD780949, uPD78F0974,uPD78F0949, uPD78F0826, uPD78F0828, uPD78F0828A M1 etc.

24-6

TMS Adapter is used to program TMS370 series MCU’s, chips supported as follows:
TMS370C758A, TMS370C742A, TMS370C702, TMS370C058A, TMS370C042A, TMS370C002A, TMS370C756A, TMS370C056A etc

24-7

HC08 Adapter is used to program Motorola HC08 series MCU’s (with security passed).

24-8

HCS12 in-circuit Adapter support mileage correction for BMW CAS/MB EZS/DASHBOARDS/MODULES/ with 912/9s12/9s12x MCU, in circuit programming ( no need removing mcu), can read/edit/write eeprom of MCU, mileage calculation integrated in soft.

24-9

EWS Adapter is used to program EWS of E38 / E39 / E46 / E53 by K-line.

24-10

ST624X Adapter is used to program ST624X series MCU’s.

24-11

OBD adapter is used for ordinary and advanced diagnosis operations, such as programming of all BMW CAS / LCM / EWS and mileage correction of all VW series and AUDI series.

24-12

HC05 Adapter is used to program MC68HC705B16/32, MC68HC705X16/32, MC68HC05B6/8/16 /32, MC68HC05X16/32series MCU,s (with security passed).

24-13

HC(7)11 Adapter is used to program MC68HC(7)11 series MCU,s (with security passed).

24-14

TMS374 Adapter is used to program TMS374 MCU’s and support immo function of DAEWOO, FIAT, KIA, PEUGEOT, RENAULT, etc.

24-15

CMM Adapter support odometer correction of E36, E38, FORD FOCUS, HONDA ACCORD V6, and HONDA CRV over the plug.

24-16

Launch X431 V 8″ full-system scanner needs no authorization no IP limitation

Launch X431 V Lenovo Tablet full-system diagnostic tool does not need to authorize by sending SN, Country and Language to the seller and wait 2 working days, also registration has no IP limitation (Except China) with dealer code 755D. Moreover, full range car models and full car system diagnosis make X431 V a professional automotive diagnostic tool.

X431 V 8″ inherits many advantages of X-431 V 7″ such as the full-system diagnosis and full range car models, communicate via Wifi /Bluetooth etc., meanwhile it improve in specification and vehicle coverage compare with X-431 V 7″ (X431 Pro) (for more Launch X431 V 8″ compare X431 V 7″ , go to read in the last paragraph).

19-1

X431 V 8” diagnostic scanner is powerful and user-friendly:
1.Performfull-system diagnosis by pairing DBSCAR adapter to Bluetooth (same as X431 V 7″)
2.Support up to 69 car brands about 220 car models from European, USA and Asian;
3.With 2–year free updateon the official site com (same as X431 V 7″)
4.Android 4.2 platformwith fast running speed, clear and user-friendly interface
5.Take advantage of android system, it integrates more application and service, such as creating maintenance data base and case library, providing instant maintenance information, establishing public and private maintenance social circle etc.
6.Reasonable PDA designand easy to carry.
7.Wifi:Built-in Wi-Fi module makes surfing on the internet freely (same as X431 V 7″);
8.Bluetooth: Communicate via Bluetooth (same asX431 V 7″)
9.Registration with dealer code: 755D, has no IP limitation, no need send country, language for activation and wait 2 working days, you could directly use.

Launch X431 V 8” surpasses other similar diagnostic scanners in the following aspects:

1.Full Diagnosis Function:

X431 V is able to diagnose the electronic control system of worldwide vehicle models covering Asian, European, American and Chinese. Full range car models and full car system diagnosis make it a professional automotive diagnostic tool.

Diagnosis functions include: Read DTCs, Clear DTCs, Read DataStream, Special functions etc;

19-2

2.Special function:

X431 V is with special function such as BMW idle study, BMW injection rate adjustment, BMW battery replacement, Nissan matching key.

3.X431 V 8”connectivity: via Bluetooth, Bluetooth distance: 10M (Without Obstacle)

You could use GOLO connector to connect to the smart phone, then you can do all system fault diagnosis of vehicle at any time, then form a diagnosis report, and transfer the report to maintenance technicians and related personnel through the account management interface, then he get the remote consultation and repair advice.

19-3

4.Launch X431 V 8”language available: English, German, Japanese, Russian, French, Korea, Arabic, Spanish and Traditional Chinese

5.Launch X431 V 8″ Tablet menu:

Click the “Settings” to configure the personalized X-431 V;
Click “Search” to locate your target quickly and conveniently;
Click “Email” to send and receive email. External POP3 or IMAP email account for some common Web email service provider can be added;
Click “File Manager” you can manage the files or downloaded files stored in SD card efficiently;
Other Additional Functions: Alarm, calendar, calculator etc.
 
6.X431 V 8″ Specifications:
Other android-based applications can be customized to install or uninstall.
Operating system: Android 4.2
CPU: 1.3 GHz
Display: 8” TN capacitive touch screen
RAM: 1 GB
Capacity (internal / SD card):16GB
Battery: 4290 mAh
Printer: Optional (Wi-Fi)
Camera: Front 2 mp / Back 5mp
Communication: WiFi/Bluetooth

Package includes:
1pc x X-431 v pad computer
1pc x Password envelope
1pc x X-431 v protection sleeve
1pc x DBScar diagnostic connector
1pc x OBD II extension cable
1pc x Cigarette lighter cable
1pc x Power adaptor
1pc x USB data cable
1pc x Non-16pin connector

19-4

X431 V 8″ full-system scanner surpasses X431 V 7“  in specification and vehicle coverage:

1.Outlook difference:

They have different outlook

Here X431 V 7″ mux

2.Specification difference

X431 V 7″ CPU: Dual core 1GHz x431 (X431 V 8” CPU 1.3 GHz)

X431 V 7″ LCD: 7.0 inch (X431 V 8” LCD is 8.0 inch)

3.Dear code difference

X431 V 8” dealer code: 755D
X431 V 7” dealer code:  86A or 86

4.Activation difference

X431 V 7” needs to active by sending machine SN, country, language to active and wait 2 working days.

5.Vehicle coverage difference

X431 V 7”: covers up to 59 car brands from European, USA and Asian
X431 V 8”: covers up to car brands about 220 car models from European, USA and Asian

6.Language difference

X431 V 7”:

English,German,Japanese,Russian,French,Spanish,Portuguese,Polish,Turkish,Dutch,Greek,Hungarian,Arabic,Danish,Korean,Persian,Romania,Serbian,Finnish,Swedish,Czech,Simplified Chinese,traditional Chinese

X431 V 8”: English, German, Japanese, Russian, French, Korea, Arabic and Spanish

SKP900 Install Driver

For the first time to connect your device with PC via a USB cable, the computer screen will remind you install the SKP-900 USB driver as follow:

14-1

Change selection->

14-2

Next->

14-3

Next->

14-4

Browse the USB driver folder->

14-5

OK->

14-6
14-7

Continue Anyway->

14-8
14-9
Click Finish, wait about 2 seconds->

14-10
Change select->

14-11

Next->

14-12

Next->

14-13

Click Continue Anyway->

14-14

Click Finish.

14-15

Installation finished.

Control Module Stand-Alone Programming Adapter (J-45211) for Cadillacs

9-1

The J-45211 control module stand-alone programming adapter (Figure VIIC-41), also called the PCM programming adapter harness, is used to connect the Tech 2 to a vehicle’s PCM and perform SPS functions for the 2000 or later Cadillac models DeVille, Seville, and Eldorado. The J-45211 isolates the PCM from a vehicle’s electrical system so that the activity of other on-board computers cannot interrupt the communication between the Tech 2 and the PCM.

NOTICE: Failure to maintain unbroken J-45211 connections (PCM, Tech 2, power, and ground) throughout the entire programming procedure may cause an interruption, resulting in PERMANENT PCM DAMAGE

Procedure for Using the J-45211 Tool:
1.  Ensure that the Techline terminal and the GM Tech2 Scanner are updated with their latest respective software.
2.  Turn the vehicle ignition off and remove the key from the ignition lock cylinder. Turn off all electrical power consumers and accessories.
3.  Open the hood and measure the battery voltage directly at the battery positive and negative terminals using the J-39200 digital multimeter. If the negative battery terminal is inaccessible, or the battery is notlocated under the hood, check the voltage between engine block ground and the underhood “+” junction block.
4.  If the vehicle’s battery voltage is not 12.0 volts or higher, charge the battery before continuing. When finished charging the battery, disconnect the charger from the battery before programming the PCM.
5. Locate the PCM and disconnect the vehicle harness connectors from the PCM.
6. Connect the J-45211 harness connectors to the PCM.
7. Connect the J-45211 power clips directly to the vehicle battery terminals. If the battery terminals are inaccessible, or the battery is not located under the hood, then connect to the engine block(ground), and to the underhood source of vehicle battery’s positive 12-volt power.
8. Observe the red battery LED on the J-45211. The red LED should remain lit whenever the J-45211 is connected to the battery voltage. If the red LED does not illuminate, check the tool’s five-amp fuse. If the fuse is good and yet the red LED will not illuminate,for assistance.
9. Toggle the power switch on J-45211 to apply ignition voltage to the Auto Scanner Tool.
10. The yellow and green LEDs should illuminate when the power switch is toggled on. The yellow LED monitors the ignition voltage being applied to the control module. The green LEDs are a feedback signal from the control module indicating that the modules’s internal circuits are operating.
11. Connect the Tech 2 to the J-45211 and enter Service Programming System.
12. Select and perform Request Information.
13. After the Tech 2 has completed the information request, toggle the J-45211 switch off.
14. Turn off the Tech 2 and disconnect it from the J-45211.
15. Connect the Tech 2 to the Techline terminal. Download the new PCM calibration into the Tech 2 using the Techline terminal and TIS software. After the download into the Tech 2 from Obd2tool.com is complete, disconnect the Tech 2 from the Techline terminal.
16. Reconnect Tech 2 to J-45211 and toggle the tool’s power switch on.
17. Enter Service Programming System, and select and perform Program.
18. After programming is complete, toggle the J-45211 switch off, and wait until the green LEDs turn off before continuing or disconnecting any connectors.
19. Turn off the Tech 2 and disconnect it from the J-45211.
20. Disconnect the J-45211 from the PCM.
21. Disconnect the power clips from the vehicle battery terminals.
22. Reconnect the vehicle harness connectors to the PCM and reinstall PCM.
23. Connect the Tech 2 to the DLC connector under the instrument panel, and start the engine.
24. Turn the Tech 2 on, “build” the vehicle, and select Diagnostic Circuit Check, then Clear All DTCs.

Note:This will clear all DTCs in all control modules simultaneously.

25. If the Service Engine Soon light comes back on after clearing  DTCs, another problem may be present or a CKP System Variation Learn Procedure may need to be performed. Follow existing service manual procedures.