Engine Vacuum Leak Symptoms and Solutions

15-1

If your vehicle has an engine vacuum leak, the air-fuel ratio in your engine will be higher than 14.7:1, also called a “lean” mixture. This ratio means that there is too much air in your engine, and as a result, the engine will run poorly or not at all. If you suspect that your vehicle has a vacuum leak, read on to learn the most common symptoms, as well as how to fix them.

Common Symptoms of an Engine Vacuum Leak

Engine vacuum leaks are commonly associated with the following symptoms, but keep in mind that this is not an exhaustive list.

Engine Running Problems

An engine with a vacuum leak could potentially run normally, but it may idle faster than usual, idle roughly, misfire, hesitate, or stall. You may find your vehicle doesn’t accelerate as well as it typically does. Major intake leaks might prevent the engine from starting at all.

Fuel Economy and Emissions

The lean air-fuel ratio will burn hotter and increase the generation of oxide emissions, such as nitrogen oxide (NOx) and sulfur oxide (SOx). Even if the check engine light isn’t triggered, the vehicle may still fail emissions testing. Drivers would also note reduced fuel economy as the engine controller attempts to compensate by adding more fuel. The evaporative emissions control system (EVAP) also depends on vacuum to function, so a vacuum leak in an EVAP valve or tubing might set an emissions diagnostic trouble code (DTC).

Check Engine Light

The engine control module (ECM) continuously monitors the environment in the engine. Using the manifold absolute pressure (MAP) sensor or mass air flow (MAF) sensor, among others, the ECM modulates fuel injector pulse, spark timing, and valve timing. If there is a vacuum leak, the ECM may be unable to compensate. Short-term or long-term fuel trim, STFT or LTFT on a scan tool Automotive Repair Software, might show something like +10% or +25% as the ECM attempts to compensate for unmetered air. P0171 and P0174 are common Fuel System Lean DTC.

Engine Damage

At its worst, long-term driving with a vacuum leak, elevated temperatures generated by running a lean air-fuel ratio could result in engine damage. Lean mixtures can detonate, damaging pistons and bearings. Higher than normal exhaust temperatures can also lead to catalytic converter meltdown.

Other Issues

Depending on where the vacuum leak is located, it could cause a variety of other problems. Some fuel pressure regulators are vacuum modulated, and so would jump to high pressure when vacuum is lost. This could result in fuel trim problems and a check engine light, possibly with Fuel System Rich DTCs, such as P0172 or P0175. Some older power steering systems idle-up the engine using a vacuum switching valve (VSV), but a vacuum leak might stall the engine during a parking maneuver. Many vehicles use a vacuum-actuated brake booster, reducing braking effort, but a vacuum leak here might make it harder to stop your car.

Identifying an Engine Vacuum Leak

There are several methods you can use to identify a vacuum leak. Start with a vacuum hose diagram, which you can find in a repair manual or sometimes on a sticker under the hood. Using one of the following methods, finding the vacuum leak might manifest itself as a change in engine speed or idle smoothness. Smaller leaks may only manifest themselves as fluctuating STFT readings on a OBD2 vehicle scanner.

Visual Check

A visual check is a good way to start, particularly with vacuum hoses and tubes. Exposed to extreme under-hood temperatures and oxygen in the atmosphere, rubber vacuum hoses and plastic vacuum tubes can become stiff or brittle, easily cracking or breaking. Similarly, rubber engine intake tubes can also become brittle, cracking and opening a way for unmetered air to get into the system. Physically manipulating these components with the engine running might reveal the leak.

Water Method

This is the simplest and cheapest method, as it utilizes just a simple spray bottle of water. With the engine running, spray water around suspected vacuum leak areas, such as vacuum hose fittings, intake manifold gaskets, and throttle plate bushings. A vacuum leak will suck in water, temporarily “sealing” the leak. This tiny amount of water won’t do any damage to your engine.

Carb Cleaner

Another method is to use a can of carburetor cleaner or intake cleaner spray. Please note that carb cleaner is flammable, so caution must be exercised and a fire extinguisher must be kept close at hand.. Sparingly spray the cleaner to suspect vacuum leak areas, while the engine is idling. If the leak is found, the engine will likely smooth out as the flammable mixture makes up for the lean air-fuel ratio.

Propane

This is a time-tested method for finding vacuum leaks, working on a principle similar to using carb cleaner. Use a small unlit propane torch, such as used for brazing or soldering, and a length of rubber hose. Poke the end of the hose around suspect vacuum leak areas with the engine idling. If the leak is found, the engine will probably speed up or smooth out as the flammable gas “compensates” for the lean AFR. Again, please note that propane is flammable, so caution must be exercised and a fire extinguisher must be kept close at hand.

Mechanic’s Stethoscope

Using a mechanic’s stethoscope with the probe removed and a length of hose, poke around suspected leak areas while the engine is running. Don’t forget to check around the vacuum brake booster, both in the engine bay and behind the brake pedal. Smaller leaks might be difficult to pinpoint, but a trained ear can pick up the distinctive hissing or whistling sound emitted by a vacuum leak.

Bubble Test

If you have access to an air compressor with a good regulator, introduce no more than 2 psi air into the intake with the engine off. (Under 2 psi is critical, as you can damage sensors or valves or create new leaks with higher psi.) Seal off the throttle body and exhaust, then use a soapy-water mixture to spray down the engine. Vacuum leaks may be revealed by the mixture bubbling up at the site of the leak.

Smoke Machine

This is the most expensive and safest method, but usually yields the best results. Not everyone has access to these expensive tools, but it may be necessary if the vacuum leak eludes you. With the engine off, plug the intake and exhaust and start the smoke machine injecting smoke into the intake. The harmless smoke, vaporized mineral oil, might take a couple minutes to fill the system, and will then start looking for ways to get out. A tiny plume of smoke will reveal vacuum leaks, so it’s best to do this test in an area free of drafts or wind.

Once you’ve identified the source of the leak, the obvious solution is to repair it, but it isn’t always a simple fix. Vacuum hoses can be replaced easily, as can sensor or tube O-rings, and some valves are also easy to replace. Other vacuum leaks might be more difficult and time-consuming, such as intake manifold gaskets or a faulty brake booster. As always, if you feel like the job is beyond you, check with your local trusted mechanic for professional assistance. Don’t forget to reset the check engine light when you’re done making repairs.

Mitchell OnDemand 5 quarter 2013 description of the catalogue

Powerful yet simple to navigate, Mitchell 1′s OnDemand Repair has been completely redesigned to deliver sophisticated search capability with increased speed. You’ll save valuable time using brand new shortcuts to TSBs, wiring diagrams, and more!
Mitchell On Demand 5 1983-current year Domestic & Import Model Coverage
Clear, Concise Illustrations & Diagrams
Time-saving TSBs, Recalls, & Technical Tips
Detailed, Accurate Repair Articles
Model-Specific Maintenance Schedules
Electronic Component Locator for all Models
Mitchell On Demand 5 OEM wiring diagrams tend to vary between manufacturers because there really isn’t an industry formatting standard. We completely redraw the majority of the OEM wiring diagram before they go into our database, meticulously verifying every detail. The end result is a consistent look and feel to every diagram in our products. And because they’re redrawn – not scanned – they take up much less space on a CD-ROM or DVD, allowing us to put more information on each disc. This increases your computer’s access speed because your CPU has smaller files to chase down.
Our customers said they want to swap discs as little as possible so they can spend more time repairing cars. To accomplish this, Mitchell uses the latest in compression technology, giving you all the data available to fix the vehicles in your shop on fewer CDs or, better yet, a single DVD for Domestic, and one for Import.
For example, our tables take up less space because the overwhelming majority are not scanned. A scanned table uses up to 68 times more space on a disc than our specially formatted tables. Taking up less space means we can include more model-specific information, giving you exactly what you need.
Mitchell On Demand 5, the automotive aftermarket’s most comprehensive repair coverage for domestic and import vehicles, now offers an impressive multi-user capability for computer networks.
In addition, users can now choose to purchase coverage for domestic or import repair information on OnDemand5′s professional interface. Version Mitchell On Demand 5 also offers an improved search with advanced functionality that maximizes search results.
“With each new version of OnDemand 5, repair shops get the most updated industry information available anywhere,” said David Niemiec, vice president of marketing for Mitchell 1. “When shops are equipped with the very best, they function more efficiently and improve profitability.”
Overall,
Mitchell On Demand 5 Repair and Estimator offer the industry’s most comprehensive repair coverage and parts and labor database. OnDemand5 Version 5.8 Repair includes repair information for 1983 to current year domestic and import cars, light trucks and vans. OnDemand5 Version 5.8 Estimator gives accurate labor times for 1974 to current year domestic and import vehicle models.
Powerful yet simple to navigate, the Mitchell On Demand 5 Version 5.8 products also deliver a sophisticated search capability with a simple and intuitive layout.
Key features for OnDemand5 Version 5.8 Repair and Estimator include:
Categories within Repair and Estimator are streamlined to allow users to navigate between Repair and Estimator without reselecting the category
A parts and labor search that finds matching parts and labor information
Listings for new fluid capacities
An estimating quotes screen view that is completely flexible and customizable
The ability to save estimates
Single click access to TSBs and maintenance schedules
NAPA part numbers and prices included at no extra charge. A free NAPA parts catalog is included with OnDemand version 5.8 Estimator.
Additional product features and benefits include:
Single Vehicle Selection. Choose one year, make and model to access repair, estimating, or maintenance data that applies to a particular vehicle configuration.
Mitchell On Demand 5 TSBs/Recalls/Tech Tips. Helpful tools that allow users to find shortcuts and diagnostic aides for the most difficult problems.
2015 Mitchell OnDemand Repair Articles, Specifications, Illustrations. Clear repair procedures, including diagnostics, enhanced by useful graphics and specifications.
Mitchell On Demand 5 Wiring Diagrams. System diagrams can be printed, usually on one page, and brought to the vehicle to speed diagnosis. A consistent format includes connector, ground and component locations.
Mitchell On Demand 5 Electrical Component Locators. Locators help technicians find important electrical components.
Mitchell On Demand 5 ScanLink Interface. A powerful diagnostic tool that helps interpret and display Snap-on scan tool data.
Mitchell On Demand 5 Quick Access. Frequently used data, such as technical service bulletins and scheduled maintenance services, is readily available.
Search Wizard. Finding key words and phrases is easier using a familiar Internet-style search interface.