How to program fobik with wiTECH app

Confirmed! Chrysler wiTech MicroPod 2 clone is able to do online programming to Chrysler including ECU programming and key adding even when all keys are lost. Here you go.

Purpose: Micropod 2 clone programs new key fobik to Chrysler 200 when all keys are lost

Car: 2015 Chrysler 200 (The 2015 Chrysler 200, along with other Fiat-based models like the Jeep Renegade, Jeep Cherokee, and Ram Promaster, are all equipped with a rolling PIN Code.)

What you need:
Locksmith Identification Number (LSID through NASTF)
Proper keys to be programmed
PIN Code
Laptop
MicroPOD II good quality clone or the genuine
wiTECH diagnostic application

Before you begin the programming process, you should the Key Code (key cut code) and Authorized PIN (key programming).

VERY VERY VERY IMPORTANT:

*   You must be online to program the key with OBD2 Scanner Micropod 2 clone.
*   You can pull the PIN Code with OBDSTAR F104 key tool.
*   If you input the wrong code for 3 times, it locks the BCM and you cannot service the vehicle for 24 hours.
*   The key is one-time programmable. Once married to the vehicle it is locked to the car forever. The key can be erased from the car and put back into the same car, but can’t be switched to another car.
*   The placement of the key during initialization is important. It needs to be placed either behind the shifter or in the center console.

How to program fobik with wiTECH app:

Step 1:

Plug the microPOD II adapter into the OBD port and connect the USB cable from the device to your laptop. This wakes the BUS on the car.

Step 2:

4-1

Manually enter the VIN of the vehicle. This gives you access to the module list.  Select the RFH (Radio Frequency Hub) module. This is the module where the key is registered.

Step 3:

4-2

Next select “Miscellaneous Functions,” then “Program Ignition Fobiks.”  At this point, you are prompted to enter the VIN again, followed by the four-digit PIN Code.

Step 4:

4-3

After the four-digit pin is entered you are prompted to hit continue to “Program Ignition FOBIK.” Once you hit continue you must press the UNLOCK button on the FOBIK within 30 seconds (the FOBIK needs to be located near the center console during this procedure).

Step 5:

4-4

Programming of the Ignition FOBIK is now successful. The new key key is accepted into the car, and the ignition will now turn on and start the car. At this point, you also have the option to program a second key with wiTech application.

How To Register Diagnostic Tools – wiTECH 1 (CHRYSLER SUPPLIER AND CORPORATE USERS ONLY)

This article applies to internal Chrysler corporate users or suppliers who have unregistered diagnostic tools such as wiTECH VCI Pod, StarMOBILE and microPOD. Upon using Chrysler witech MicroPod 2 with an unregistered tool, users will see a pop up message similar to “Warning!! The {your device-type} you are connecting to is not registered”.

DESCRIPTION:

If you received a warning in wiTECH stating that your device is not registered, please follow the instructions below to register your dealership’s diagnostic tools.  Failure to register will result in wiTECH not being allowed to run with your diagnostic tools!

PROCEDURE:

You should email the wiTECH Premium Support Help Desk at support@witechtools.com with your entire list of diagnostic tools (wiTECH Pod, StarMOBILE, microPOD) that you are responsible for. This will allow the registration of ALL of your diagnostic tools at once. The email should include the following, or there may be a delay in registering the devices:

EMAIL CONTENTS
Subject Line:*    “Car Diagnostic Tool wiTECH Diagnostic Tool Registration”

Include in Body of Email:

*   wiTECH Account Number
*   Contact Name
*   Contact Phone
*   Diagnostic Tool Serial Numbers:
*   VCI Pod (WVP-xxxxx located on the bottom of the device)
*   StarMOBILE (Cxxxx-xxxxx located on the bottom of the system status screen or on the tool belt loop)
*   microPOD (WCP-xxxxx or WSP-xxxxx or WMP-xxxxx located on the back of the device along the barcode)

When the diagnostic tools have been registered, wiTECH users will no longer receive the pop-up warning about an unregistered diagnostic tool.

Please note: This process can take up to 48 hours to be completed.

microPod II Configuration

1. On a PC with the wiTECH Application installed, connect the Micropod II with a USB cable and enter
IP “172.22.22.22” into the address bar of an Internet browser.
2. Select Wireless Settings in the menu on the left

14-1

3. Select New and enter the name of your profile that you are creating and select Add

14-2

4. In the Security Settings field enter the Automotive Scan Tool wiTECH Access Gateway wireless profile credentials
* SSID,
* Security: WPA PSK,
* Enter Key:
* Confirm Key:

14-3

5. Select Save at the top of page

14-4

6. Select Close on the next page

14-5

7. Select Manage Networks in the menu on the left

14-6

8. Select radio button for the wireless interface

14-7

9. Next to the profile that was just created select the Select & Start button

14-8

10. Select Close on the next page

14-9

11. Once the connection is complete you will see an IP address populate for the wireless interface
? In some cases you may need to select the refresh button

14-10

12. If you have tried selecting the refresh button and the tool is still not obtaining an IP address
? Select the radio button next to the wireless interface

14-11

13. Select the Disable button in the Wireless Adapter area

14-12

14. Select OK on the warning pop up

14-13
15. Select Close

14-14

16. Select the radio button for the wireless interface

14-15

17. Select the Enable button in the Wireless Adapter area

14-16

18. Select Close

14-17

19. You will now see an IP address for the wireless interface

14-18

20. If you are still unable to acquire an IP, make sure you are within range of the wiTECH wireless network try moving closer to the OBD II Scanner wiTECH Access Gateway

High-quality witech micropod system vs. bad micropod 2 china clone

Here’s a comparison chart of genuine vs. clone wiTech MicroPod 2 system, incl. High-quality witech micropod system vs. bad micropod 2 china clone.

Genuine WiTech Micropod2 vs. Clone wiTech Micropod II

4-1

4-2 4-3 4-4

witech micropod2 for sale:

http://www.obd2tool.com/goods-5172-wiTech+MicroPod+2+for+Chrysler+Diagnostic+Tool.html

4-5

– the copy is 1:1 of the genuine, of high quality and good stability, its connector matches the car OBD plug perfectly.

– With high-quality USB cable which transfer data stably and reliably

– The package is anti-static, moisture-proof, anti-electromagnetic interference

– Workable with your current wiTECH software

– No smart cables required

– No drivers needed

micropod 2 ebay?

Ebay should be a good place to buy items. But for professional vehicle diagnostic tools, a site with experienced experts and technical support teams like www.obd2tool.com

witech micropod II HQ Clone Customer Review:
Just ordered a chinese clone MicroPod II and it has been working exactly like an OEM unit. No errors so far and tested functions on 3 different vehicles. It has been confirmed working with unmodified software wiTECH v17.03.10 (downloaded directly from Chrysler). For now it works fine.

I have tested Dodge also. I just used it on a 2014 dodge avenger just fine.

I don’t have experience with Windows XP. This version of Witech works fine on Windows 7 and Windows 10.

I have also uploaded pictures of the internals for those who are curious.

4-6 4-7 4-8 4-9 4-10

witech software download:

http://cheapobd2tool.com/2017/09/13/free-download-v17-03-01-witech-micropod-2-for-chrysler/

micropod 2 login, setup

http://cheapobd2.com/2017/09/13/how-to-set-up-witech-micropod-2-chrysler-diagnostic-tool/

witech micropod 2 review:

http://forobd2tool.com/blog/2017/09/13/review-on-chrysler-witech-micropod-2-diagnostic-system/

How to use Chrysler wiTech MicroPod 2 Diagnostic Programming Tool ?

1. Please confirm that you have successfully installed the software.

If you don’t know how to install Chrysler wiTech MicroPod 2 software, please check this link:

http://www.obd2tool.com/blog/2017/05/12/how-to-install-chrysler-witech-micropod-2-diagnostic-programming-tool/

2.Connect Chrysler wiTech MicroPod 2 USB Port with PC, OBD2 Port connect with car.

3.The computer will automatically install Chrysler wiTech MicroPod 2 hardware driver

11

12

4.After Drive installed, you can find your device in your computer device manager

13

5.Double click the icon of Chrysler wiTech MicroPod 2

14

6.You will see Chrysler wiTech MicroPod 2 connected with software, Please click ” next”

15

7. If you have your personal online account, you can login in your user id and password. If you don’t have online account, please select “word off line”,Then click “finish” and go to next step

16

8. Select ” Connect”
17

18

9. To this step, you can choose the type of car which you want to test and the system for diagnosis and programming.

Posted in Car Diagnostic Tools | Tagged , , , | Comments Off

How to install Chrysler wiTech MicroPod 2 Diagnostic Programming Tool?

WARNING; The computer on the day of the date

1.PC-Based: Requires PC connected to the network

1

2.Run Chrysler wiTech MicroPod 2 CD software as picture

2

3.Firstly, installation AdobeAIRInstaller.exe

3

4.Secondly, installation jre-6u45-windows-i586.exe

4

5. Finally, installation wiTECH_Install_17.03.10.exe

5

6.After successful to install the software, the desktop will appear Chrysler wiTech MicroPod 2 software icon is as follows:

6

7. The specific installation process, please watch the following installation video: