Why do you need VCM II recovery

Why do you need have FORD VCM firmware recovery?
You Chinese clone that after flashing says beep every second …
or firmware in the clone for IDS84 program , and you want the software to IDS86 …
or you have violated the data on the memory card or memory card is broken …

Is it safe to do VCM II recovery?
Not really. ALL can be done AT YOUR SOLE RISK . You’d better SAVE YOUR OLD MEMORY CARD .

How to do VCM II recovery?

Install a clean copy of the operating system, this system must not be connected ford vcm
2. Install the drivers for all devices and update system
3. Download files from the links below
4. Disable updates Disable Firewall, Disable Web
5. Set the date on your computer September 1, 2013, and disable time synchronization via the Internet.
6. Set IDSv86 on your system.
7. reboot
8. kill the following processes if they are running:
CodeServeD.exe
DetectionManager.exe
EngineeringFeedback.exe
FNPLicesingService.exe
ISUSPM.exe
ProbeTickHander
Starburst.exe
SysPage.exe
TDSNetConfig.exe
TDSNetSetup.exe
Tabman.exe
testman.exe
wuauclt.exe
XMLRegistryD.exe
9. This item is optional.
unzip the boot.zip and put it in the folder “C: \ Program Files \ ford motor company \ IDS \ system”
that is, the full name of the folder should be “C: \ Program Files \ ford motor company \ IDS \ system \ boot”
10. Apply the patch from attachments. Up to this point NOT connect device VCM2. 2nd item when using the patch (for VCM 2).
11. Reboot
12. WARNING! your device VCM2 must not connected wires.
13. Remove the side cover from VCM2 with the side where drawn Wifi, install the card 4 or 8GB depending on what was installed in your device. Commonly used
class 4 cards
14. Press the plastic button (to the quiet click) but not much, because the Chinese are very fond of buttons to break.
15. connect the +12 v supply through connector. (Continue to hold the button)
16. Wait a few seconds, the red light, but you must continue to hold the button. When a beep sounds immediately release the button.
17. Wait about two minutes (visually nothing will happen), connect the USB cord from VCM2 to computer.
18. Start Bosh VCI MANAGER. Once connected, you will see your VCM2 in recovery mode.
19. click on “Restore” button and go to drink coffee, it takes about 40 minutes.
20. after flashing VCM2 automatically reboot. (If, after repeated firmware situation BEEP 1 second, you can try to do firmware lower software version number,
eg 84 or 85)
21. Wait 2 minutes.
22. unplug all cables from VCM2 from OBD2TOOL
23. Restart the computer, wait for the full load and run the IDS86 (VCM2 not connected). on offer data entry, enter the dealer Ford / Mercury / Lincoln,
dealer code UR097, country Russia
24. Wait until the start IDS86 and connect the device.
25. system will install the drivers and communication protocols VCM2
Everything should work!
p.s. If you broke the paragraph 14 of the button to close the tweezers solder contacts or temporarily remote button on the wires.
If this does not help, follow instructions at the end of all the action as follows:
26. Reboot
27. Press the reset button, plug in the +12v to VCM2, wait for beep, release the reset button
28. Start IDS86 and wait until the boot
29. Connect VCM2 USB cable to the computer program IDSv86 should offer to update the firmware of the device.
30. Update the device.
31. after flashing VCM2 automatically reboot. (If, after repeated firmware situation BEEP 1 second, you can try to do firmware lower software version number,
eg 84 or 85)
32. Wait 2 minutes.
33. unplug all cables from VCM 2
Now exactly Everything should work!

How to Choose the right OBD2 Scanner For Ford Cars

“What is the best OBDII Diagnostic Scanner For Ford Cars by far ? “ This is always a super hot topic to be talked by many ford cars lovers in the forum. So,today,i will share a buyer guide on how to choose the right OBD2 Scanner For Ford Cars for all customers,mainly based on forum number’s experience,hope it will be useful

1.Full Chip VCM 2 VCMII OBD2 Diagnostic Tool—-Recommended by most users with a good reputation

VCM II is the new Ford Scan Tool to provide dealer-level diagnostics capabilities for most 16 pin cars 1996-2015, including for all new 2013 vehicles by using the IDS software. It can support Ford / Mazda Gasoline / Diesel Cars From 1996 to 2015. VCM 2 has launched for ages,tested by many users and there are also many good reviews about VCM II and following are good reasons to account for why VCM2 IDS was so hot

1.)With great PCB board,well made with top quality

Ford VCM II VCM 2 IDS Diagnostic Tool

9-1

2.)Multi-Languages Supported

9-2

3.)VCM II Scan tool can do diagnose, scan, airbag, key programming, ecu programming, PCM programming via OBD2 port.

4.)Support VMM and CFR.

5.)For Ford IDS V101 and Mazda IDS V94 ,provides dealer-level diagnostics using the IDS software.

6.) Decent quality and price.

2.Launch DIY Scanner CReader 8021 Full OBD2 diagnostic Scanner

Launch CReader 8021 will be another popular recommended OBD2 diagnostic Scanner For Ford cars.See pix show

9-3

CReader 8021 is a small-size multipurpose CReader. It provides ten OBDII/EOBD diagnostic modes and also the following functions : oil reset, set service mileage, EPB reset.In addition, it supports ABS and SRS diagnosis to facilitate all-around car detection,see function below

1. OBD full functions
Read dynamic data streams and MIL
Read readiness status
Query freeze frame data
Read current DTCs
Clear DTCs
O2 sensor test
On-board monitor test
Read pending DTCs
On-board system or component control
Read vehicle information
Read permanent DTCs

2. Oil reset
3. Electrical Parking Brake(EPB) reset
4. Battery Management System(BMS) reset
5. Steering Angle Sensor(SAS) reset
6. Read DTCs, clear DTCs, and read data streams for the ABS system
7. Read DTCs, clear DTCs, and read data streams for the SRS system
8. Color and graphical display of data streams
9. Query DTCs
10. Free update via internet
11. Multilingual support
12. Print data via PC

And now obd2tool.com provided a cheap wholesale price for quality CReader 8021,only $199USD by free DHL shipping.

More OBDII Diagnostic Tools can be found at www.obd2tool.com and if you have any questions or doubts about product,pls dont hesitant to contac us freely.

Ford VCM 2 VCM II IDS FAQs Guide For Customers

OEM VCM 2 IDS For Ford Diagnostic and Key Programming Tool Full Chip Version was one of bestselling diagnostic tool for Ford IDS V101 and Mazda V94. Ford VCM II VCM 2 provides dealer-level diagnostics using the IDS software and supports multi-functions with a great performance at decent price. Maybe just these reasons to account for why VCM II was so hot and popular. And Following are some FAQs that customers maybe most cared and hope it will be useful.

Q1: When i installed Ford VCM II on Windows 7 system,there is an error read as “unregistered USB device”,what should i do?Please help.
A1: Please change your system to Windows XP or Change another windows XP computer to install.

Q2 : What is the big different between VXDIAG VCX NANO and VCM 2 ?
A2 : Both are amazing diagnostic tools,and you can check the comparison between them right here to get more useful informations : Ford VCM II vs VXDIAG VCX NANO ( Red ) vs VXDIAG VCX Pro 3 in 1

Q3 : Is the VCM II IDS original one or clone one ?
A3 : The Ford VCM II we sold was china version,but we can promise,the quality is super high and 100% working,this tool has been tested by so many Obd2tool.com customers,till now,didnt receive any complain.

Q4 : Can VCM II program module?Like Fuel injection control module?
A4 : Yes,it can program module,Fuel injection control module is a part of engine ecu

Q5 : Whether the VCM II can work on Ford Crown Victoria 1998?
A5 : If this car support standard OBD2 connector, it can work on it. It can support Ford / Mazda Gasoline / Diesel Cars From 1996 to 2015,which provides full dealer diagnostic capabilities for most 16 pin cars 1996-2015, including for all new 2013 vehicles.

Q6 : How can I get incode for key programming?
A6 : You need to get the incode by Ford Outcode/Incode Calculator first, then use the VCM to do keys(If you have other tool to get the incode, it is ok as well)

Q7 :  How to install DFStd Freeze Software For Ford VCM II Diagnostic Tool ?
A7 :  you can check it here to find useful guide : Ford VCM 2 VCM II IDS Guide : How to Install DFStd Freeze Software

Q8 : Is it easy to use FORD VCM II VCM 2 ?
A8 : yeah,it is easy to use and just in case of your need,here is a VCM II User Guide For Ford and Mazda users : How to Use Ford VCM II VCM 2 IDS Scan Tool For Ford V101.03 Mazda V94

Q9 :  How’s Ford VCM 2 PCB ?
A9 : it is well made with great quality,see here

4-1

4-2

The using experience of VCM II

 

 

I recently had an issue with a Mazda III 1.6HDI 2006 the ECU has lost it’s parameters of PATS System, so i decided to buy a VCMII and installed the IDS Mazda V92.04 in a VmWare in order to repair the car. So i have received my Ford VCM II and though everything will be okay when i will connect to the car.

So i go to the car, connect the VCI it looks starting ok, Windows finds the correct drivers but VCI Manager for Ford-VCM don’t see the VCM 2.I thought there is a little bug with my installation so i install IDS V91 on Windows 7 and then try to detect VCMII. Same problem, i don’t see the VCM in the Manager.

Then i decided to download the latest Bosch drivers for VCMII. First time launch Bosch says i need to update the VCM. Ok i start the Update after about 5 minuts it stucks at FPGA update problem. I don’t care restart the VCM Red/Green and beeps every 1 second. I stopped there and decided to Restore the ford vcm ii diagnostic tool to a V84 Version After multiple downgrade triyng on different Versions of IDS (Always in recovery mode).It doesn’t work on any version from V81 Up to V92. I don’t care so i decided to open it to see if it’s just a bad solder on a small compenent as always.

So i opened it resoldered resistors, capacitors, masses, With air Heating Rework machine heated the Cpu, FPU, FPGA, Ram every connector and it’s always Stuck on Update. (FPGA Update fails and 10%).

 

see more click http://www.obd2tool.com/search-VCM+II.html